- DFM first — manufacturability removes defects at the source, before any chip is cut.
- SPC with Ppk ≥ 1.67 at the initial study on key characteristics on a representative characteristic; key-characteristic target ≥ 1.67, general ≥ 1.33.
- Hexagon CMMs, laser microscope, and surface profiler for dimensional and finish verification.
- Full lot traceability through MES/ERP, on every job.
Read the tolerance band before you read the index. Cpk is a ratio of the tolerance band to the process spread, not an absolute measure of accuracy. The figure above was recorded on a length characteristic with a 0.4 mm band (76.1–76.5 mm) — wide by design. Hold the same process spread against a ±0.005 mm feature and it fails outright. Ask for the band, the subgroup count and the sampling window on every capability number a supplier quotes.
Why is quality designed in, not inspected in?
Inspection can only catch what is already made. If a design asks for a sharp internal corner, a wall too thin to clamp, or a tolerance tighter than function needs, no amount of measuring will make it reliable — it will yield poorly, slowly, and expensively. The single most important quality decision happens before cutting, when a DFM review opens that radius, thickens that wall, and loosens that tolerance. Get that right and the inspection bench confirms quality instead of rescuing a bad design. This is the first principle: quality is a property of the design, and inspection is its proof.
How is incoming material verified before machining?
Every defect chain starts with the raw stock. An alloy substitution is a latent failure, not a bargain, so every incoming lot is checked by XRF spectrometer against its mill certificate before it touches a machine. A mixed or substituted lot is caught at the door, not discovered on your receiving dock after a field failure.
How is the process controlled during machining?
A first article can be right by care; a thousand parts are only right by process control. Statistical process control runs on key characteristics — sampling, charting, and correcting the moment a dimension begins to drift toward a control limit, so the hundredth part measures like the first.
| Capability metric | Target | Record |
|---|---|---|
| Key characteristics (Cpk) | ≥ 1.67 | Cpk = 1.851 (one characteristic on one part, not a blanket capability claim) on a representative length characteristic (76.1–76.5 mm) |
| General characteristics (Cpk) | ≥ 1.33 | Held across production |
This is automotive-grade discipline, running on every job, not just the automotive ones.
How are parts verified at final inspection?
Final inspection is where the measured values become evidence. The bench is the same class of equipment a buyer would use to audit the shop, and the results are documented rather than reduced to pass/fail.
- Hexagon GLOBAL S CMMs for dimensional verification, plus a gear measuring center and vision measuring machines.
- KEYENCE VK-X3000 laser microscope and SURFCOM 1800D for surface finish and profile.
- XRF (iCHEQ) spectrometer for material composition checks.
- HVS-1000A micro-Vickers hardness tester, Fischer coating gauge, salt spray and tensile testers.
How are parts traced back to raw material?
For automotive and regulated buyers, traceability is the difference between isolating a bad lot and recalling everything. The MES/ERP system records raw material source and usage, process parameters, machine data, production batch, machining time, operator, and inspection results on every lot. If a non-conformance ever surfaces, the affected lot, machine, and operator can be isolated — and the impact contained — instead of guessed.
Is there APQP and PPAP capability?
Yes — a complete automotive APQP/PPAP package is documented for customer programs: process flow chart, control plan, SPC charts, and PFMEA. This is the same quality-planning discipline IATF 16949 audits look for, and it demonstrates that process control runs from the first article through the production run.
Which certifications back the quality system?
Certifications are the cheapest pre-audit you can run. Three are held, with scope stated honestly rather than inflated.
| Standard | Certificate number | Scope |
|---|---|---|
| ISO 9001:2015 | 116024/A/0001/UK/En | Machining of metal parts |
| IATF 16949:2016 | 131941/A/0001/SM/En | Manufacture of CNC metal machining parts (excludes product design, Clause 8.3) |
| ISO 14001:2015 | 116024/B/0001/UK/En | Environmental management related to machining of metal parts |
Honest scope note: IATF 16949 excludes product design under Clause 8.3. This is a build-to-print operation — if a program needs design ownership, that is scoped up front rather than over-promised.
What should a buyer ask about quality before ordering?
Whether you buy from this shop or another, these questions separate a documented quality system from a quality slogan.
- Can they show a real SPC chart, not a capability statement? A Cpk number without a control chart behind it is a claim, not evidence.
- Is incoming material checked against its cert? Ask how a substituted alloy is caught.
- Are inspection reports shipped with the parts? Documented values beat pass/fail stamps.
- Is the certificate number verifiable? Real ISO/IATF certificates have numbers you can check with the registrar.
Send a drawing and we will run all four on ourselves for you, in writing, before you commit.
What does a Cpk value actually mean?
Cpk is a single number that measures how well a process stays inside its tolerance band, accounting for both the spread of the measurements and how centered that spread is. A high Cpk means the process is not just accurate but consistently so; a low Cpk means the spread is crowding the tolerance limits and parts are at risk of drifting out.
| Cpk value | What it means |
|---|---|
| Below 1.0 | Not capable — the process spread already exceeds the tolerance band |
| 1.0 – 1.33 | Marginal — acceptable only for non-critical characteristics, and worth improving |
| 1.33 – 1.67 | Capable for general characteristics — the common industrial floor |
| 1.67 and above | Capable for critical characteristics — the automotive target for key dimensions |
The shop's record is Cpk = 1.851 (one characteristic on one part, not a blanket capability claim) on a representative length characteristic (76.1–76.5 mm), against an initial-study target of Ppk ≥ 1.67 on key characteristics and a production target of Cpk ≥ 1.33. The number only means something with the control chart behind it — a Cpk without a chart is a claim, not evidence.
How do first-article, in-process, and final inspection differ?
Inspection happens at three different moments, and each one catches a different class of problem. Conflating them is how a supplier hides a weak point behind a strong final report.
- First-article inspection (FAI) checks the first part against the drawing before the batch runs, catching a programming or setup error before it is repeated a thousand times.
- In-process inspection samples parts during the run, catching drift while there is still time to correct it instead of scrapping the batch.
- Final inspection verifies the finished parts, including cross-face relationships, before they ship.
A shop that only does final inspection is sorting good from bad at the end; a shop that does all three is preventing the bad from being made in the first place. On 4-axis work, in-process cross-face checks matter most, because that is where a rotary setup error would otherwise hide until assembly.
How are the measuring instruments kept accurate?
A measurement is only as good as the instrument behind it, so the instruments are calibrated and verified against traceable reference standards on a schedule — a CMM that has drifted is worse than no CMM, because it produces confident-looking wrong numbers.
- Hexagon GLOBAL S CMMs and the gear and vision measuring machines are verified so their dimensional readings stay trustworthy.
- Surface instruments — the KEYENCE VK-X3000 laser microscope and SURFCOM 1800D — are checked so an Ra reading means the same thing every week.
- Material and property instruments — the XRF spectrometer, hardness tester, coating gauge, salt spray, and tensile testers — are verified so a pass is a pass.
The same logic extends to the machine tools themselves: a tolerance claim depends on the machine holding its position, and a maintained 4-axis machine holds ±0.003 mm (milling) / ±0.002 mm (turning) on critical features because the rotary is kept accurate, not assumed accurate.
What happens when a non-conformance is found?

Every process eventually produces a bad part; the difference between a strong and a weak quality system is what happens next. The response is containment, correction, and prevention — in that order.
- Containment. The affected lot, machine, and operator are isolated using the MES/ERP traceability record, so the problem is bounded instead of guessed.
- Correction. The process is adjusted — a tool offset, a fixture, a program — and re-verified before the run resumes.
- Prevention. The root cause is recorded and the control plan updated, so the same failure does not repeat on the next lot.
This is where traceability earns its keep: without the record tying a lot back to its material, machine, and operator, containment becomes a full recall instead of a targeted fix. Ask any supplier what their non-conformance procedure is — a shop that cannot describe it in three steps does not have one.
How do you read the inspection report that ships with the parts?
The report is the part's evidence trail, and a good one shows measured values rather than a pass/fail stamp. Three documents make up the package.
- The CMM report lists each critical dimension, its tolerance, and the measured value, so you can see how close a feature ran to its limit, not just that it passed.
- The SPC chart shows the key characteristics over the run, so you can see the process stayed stable rather than drifting toward the edge.
- The material certificate ties the lot to its alloy and heat, so the grade you specified is the grade you received.
Read the report against your drawing, not against a summary. A dimension that passed at 0.0048 mm on a ±0.003 mm (milling) / ±0.002 mm (turning) limit is worth a second look, because it tells you the process is running close to the edge, and that is exactly the information a real quality system does not hide.
What this shop actually runs
We machine every part in our own 6,800 m² plant in Dongguan, China, on 100+ CNC machines with 100+ staff. The machine list by category:
- 5-axis machining centres (10+) - Mazak VARIAXIS I-600 (510/910/510 mm travel, 12,000 rpm, 22 kW, 71.6 N·m, 30-tool BT40) and Mazak INTEGREX I-250H S (B-axis 0.0001°, 24 kW, 124 N·m, 38-tool HSK-A63). Cut on compound-angle parts, single-setup multi-face prismatic work, and aerospace fittings where datum transfer loss is unacceptable.
- 3-axis / 4-axis machining centres (50+) - Brother SPEEDIO S500Z2N / S700Z2N (10,000 rpm, 14/21-tool ATC, 0.7 s tool-to-tool, Z-axis 2.2 G) and Mazak VCE-430A L / VCE-570C L (10,000 rpm, 118 N·m, 24-tool ATC). Cut on prismatic parts, plates, brackets, housings.
- Swiss-type turning centres (10+) - Citizen Cincom A20-3F7 (Φ20 mm, 10,000 rpm), TSUGAMI B0206-III / B0205-III (Φ20 mm, 0.1 µm), STAR SR-32JII / SR-32J Type N (Φ32 mm, 8,000 rpm). Cut on long, slender rotational parts at ±0.002 mm.
- CNC turning centres (20+) - HEADMAN T70M/1250 (720 mm swing, 117 mm bore, 3,000 rpm, BMT75 12-station turret). Cut on shafts, bushings, flanges up to ±0.002 mm.
- Wire EDM (5+) - Sodick AQ535L (550/350/300 mm travel, ±20° taper, 800 kg workpiece). Cut on hardened tool steel, internal splines, sharp internal corners that milling cannot reach.
- Inspection: Hexagon CMM + 20+ gauges - Hexagon CMM for coordinate measurement, plus vision system, profilometer, hardness tester, coating thickness gauge, XRF for material verification. The 10:1 rule (gauge 10x more accurate than the band) is applied to every feature.
- Machine highlights - VARIAXIS I-600: one-setup multi-face 5-axis + MAZA-CHECK auto-calibration; INTEGREX I-250H S: DONE-IN-ONE mill-turn, B-axis 0.0001° + Ai thermal shield; SPEEDIO S500Z2N / S700Z2N: Z-axis 2.2 G + 0.7 s ATC; Swiss-type: guide-bush switchable + 0.1 µm resolution.
Tolerance: ±0.003 mm CNC milling / ±0.002 mm CNC turning / ±0.002 mm grinding and wire EDM. Capability: Ppk >= 1.67 initial on key characteristics, Cpk >= 1.33 ongoing.
Certificates: ISO 9001:2015 (116024/A/0001/UK/En), IATF 16949:2016 (131941/A/0001/SM/En, with design clause 8.3 excluded, stated openly) and ISO 14001:2015 (116024/B/0001/UK/En), issued to Dongguan Zhuohang Ltd, registration 91441900MA4UWT6X39, founded 2005.
Where we ship: Austria, Belgium, the Czech Republic, Denmark, France, Germany, Greece, Hungary, Ireland, Italy, the Netherlands, Spain, Sweden and the United Kingdom in Europe; Brazil, Canada, Mexico and the United States in the Americas; China, Israel, Japan, Singapore and Sri Lanka in Asia; Australia and New Zealand in Oceania; and South Africa in Africa — plus other countries and regions worldwide, shipped from our base in Dongguan, China.
Contact: Felipe Iglesias, [email protected], +86 13126536955.
Ask for the evidence behind the quality claim.
Email [email protected] or call +86 13126536955 to see a real SPC chart and inspection report.
Frequently Asked Questions
How do you prove process capability?
In short, With SPC control charts on key characteristics. On a representative length characteristic (76.1–76.5 mm), our record shows Cpk = 1.851 (one characteristic on one part, not a blanket capability claim) against an initial-study target of Ppk ≥ 1.67.
How is incoming material verified?
Every incoming lot is checked by XRF spectrometer against its mill certificate before it reaches a machine. A mixed or substituted alloy is caught at the door, not discovered on your receiving dock.
How are dimensions verified before shipping?
Critical dimensions are measured on Hexagon GLOBAL S CMMs, with surface finish and profile on a KEYENCE VK-X3000 laser microscope and a SURFCOM 1800D. Hardness, coating thickness, salt spray, and tensile are covered in-house.
How are parts traced back to raw material?
In short, A MES/ERP system records raw material source, process parameters, machine data, batch, operator, and inspection results on every lot. A non-conformance can be traced to the specific lot, machine, and operator, and its impact contained instead of guessed.
Do you have APQP and PPAP capability?
Yes — a complete automotive APQP/PPAP package (process flow chart, control plan, SPC, PFMEA) is documented for customer programs, demonstrating automotive-grade quality planning and process control.
Are your certifications verifiable?
Yes — ISO 9001:2015 (116024/A/0001/UK/En), IATF 16949:2016 (131941/A/0001/SM/En), and ISO 14001:2015 (116024/B/0001/UK/En), each with a number you can check with the registrar. The IATF scope excludes product design under Clause 8.3.
Why does DFM matter to quality?
A part that is hard to manufacture yields poorly no matter how good the inspection is. A manufacturable design removes the root cause of defects before cutting, so SPC and CMM verification confirm quality rather than rescue a bad design.
What inspection reports ship with the parts?
CMM inspection reports, SPC charts, and material certificates ship with your parts as documented evidence of what you received, not just a pass/fail, but the measured values behind it.
What does a first-article inspection cover?
A dimensional report on the first part, measured against the drawing before the batch runs. It catches a programming or setup error before it is repeated across the run.
How are the measuring instruments kept accurate?
The CMMs, surface instruments, and material testers are calibrated and verified against traceable reference standards on a schedule, so a pass means the same thing every week.
What happens if a non-conformance is found?
Containment first — the affected lot, machine, and operator are isolated from the traceability record — then correction and prevention, so the same failure does not repeat on the next lot.
Continue reading: 3 Axis CNC Machining · 5 Axis CNC Machining
Standards referenced on this page
- IATF 16949:2016 — Automotive quality management system standard
- ASTM A582/A582M-12 — Standard Specification for Free-Machining Stainless Steel Bars
- ISO 14001 — Environmental management systems — Requirements with guidance for use



