Zhuohang Precision Machining Factory

4-Axis CNC Milling Machine: What the 4th Axis Adds

4-Axis CNC Milling Machine: What the 4th Axis Adds — The "4th axis" is a rotary table that spins your part around a horizontal or vertical axis. Tolerances: ±0.003 mm milling, ±0.002 mm turning — ISO 9001 / IATF 16949 verified.

The "4th axis" is a rotary table that spins your part around a horizontal or vertical axis. It sits between a plain 3-axis mill and a full 5-axis machine, and for a surprising range of parts it is exactly right. Here is the buyer's view.

What a 4-Axis Milling Machine Is

A 3-axis mill moves the tool in X, Y, Z. A 4-axis machine adds a rotary axis (usually called the A or B axis) — a table that rotates the workpiece so the tool can reach sides and around-the-diameter features without you unclamping. Think of it as 3-axis plus the ability to index or continuously rotate the part. The classic use: a round or polygonal part where you need features on multiple sides or around the circumference.

How It Differs from 3-Axis and 5-Axis

What the 4th Axis Does Well

It excels at: parts needing holes or features on multiple faces (indexed positioning), round parts with radial holes/slots (rotary indexing), and polygonal parts (hex, square bosses machined complete). If your part is "a block with features on four sides" or "a cylinder with holes around it," 4-axis is usually the efficient answer — more capable than 3-axis, less expensive than 5-axis.

Specifying 4-Axis Work: Tolerances, RFQ Checklist

Anodized aluminum component machined on a 5-axis machining center.

The tolerance to watch is the position of features around the rotation — governed by the rotary table's indexing accuracy and how the part is located on it. Send:

Common Mistakes Buyers Make

The error is assuming you need 5-axis when 4-axis suffices — you pay a premium for an axis you do not use. The second: not telling the shop which features are around the rotation, so they under-specify the rotary table accuracy. The third: sending a part that is genuinely 3-axis and getting quoted on a 4-axis machine anyway, adding cost with no benefit.

How Zhuohang Approaches 4-Axis

We route parts to 3-, 4-, or 5-axis based on geometry, not machine availability. If your part needs indexed side or around-axis features, 4-axis delivers them accurately and economically; if it needs two-axis tilting, we move it to 5-axis. One quality system (ISO 9001:2015, IATF 16949:2016) covers all. Talk to [email protected] about which your part needs.

What the extra axes actually buy

The axis count is about setups, not precision. A 3-axis machine cuts from one direction, so a part with features on several faces needs to be re-fixtured between operations - and every re-fixture introduces a small error. A 4-axis machine adds rotation, and a 5-axis machine can reach five sides in one setup, so the features on several faces stay in the same coordinate frame and line up. For a part that is a prismatic block, 3-axis is enough and cheapest; for a part with angled or multi-face features, the extra axes buy accuracy and fewer operations. You choose the axis count for the geometry, not by habit.

How to read an axis-based quote

If a part genuinely needs 5-axis work, the quote reflects one setup and tighter feature relationships; if a shop puts a 3-axis part on a 5-axis machine and charges for it, you are paying for capability the geometry does not use. This floor runs 3-, 4- and 5-axis machines including the Mazak VARIAXIS I-600 five-axis and the INTEGREX I-250H S mill-turn, at ±0.003 mm milled. Contact Felipe Iglesias at [email protected] or +86 13126536955 with the drawing and ask which axis count the geometry actually justifies.

How to verify the claim in one email

The fastest way to separate a real floor from a brochure is to ask for the machine list and the certificate numbers - and this facility answers in one email. Dongguan Zhuohang Ltd operates 100+ CNC machines across 6,800 m² in Hengli Town, Dongguan: Mazak VARIAXIS I-600 five-axis, INTEGREX I-250H S mill-turn, Brother SPEEDIO, and TSUGAMI, STAR and CITIZEN Swiss lathes. Inspection is on a Hexagon CMM with the 10:1 gauge rule, certification is to ISO 9001:2015, IATF 16949:2016 and ISO 14001:2015, and critical characteristics run at Ppk 1.67 initial and Cpk 1.33 in production.

Worldwide buyers across Europe, the Americas, Asia, Oceania and Africa are supplied from Dongguan. MOQ is 1 piece, lead times run roughly 3 / 7 / 30 days, and the quote from Felipe Iglesias ([email protected], +86 13126536955) comes back with the routing and the capability evidence together.

Take the next step

One drawing and one quantity is the whole hand-off. Send a STEP or IGES model and a 2D drawing with the tolerances, datums, material grade and finish, state the quantity and lead time, and the reply is an itemised quote - material, setup, cycle time, inspection - rather than a round number. If the drawing is incomplete, send what you have and the open questions; the point is to open the conversation, not to wait for a perfect package.

Contact Felipe Iglesias at [email protected] or +86 13126536955. MOQ is 1 piece, lead times run about 3 / 7 / 30 days, and the service area covers Austria, Belgium, the Czech Republic, Denmark, France, Germany, Greece, Hungary, Ireland, Italy, the Netherlands, Spain, Sweden and the United Kingdom in Europe; Brazil, Canada, Mexico and the United States in the Americas; China, Israel, Japan, Singapore and Sri Lanka in Asia; Australia and New Zealand in Oceania; and South Africa in Africa, shipped worldwide from Dongguan.

Tolerance and surface finish reference

±0.003 mm milled, ±0.002 mm turned, and ±0.002 mm ground or wire-cut, all verified on a Hexagon CMM against the datum scheme. Surface finishes span Ra 0.8 to 3.2 µm as-milled, Ra 0.2 to 0.4 µm ground, and Ra 0.05 to 0.1 µm polished. The 10:1 gauge rule governs every feature - the instrument must resolve ten times finer than the tolerance it checks. And the datum is what makes the tolerance real: read against two different datums, the same callout gives two different parts, so state the datum and the convention, ASME Y14.5 or ISO.

The material decision

Aluminium 6061-T6 leads on light and economical; 7075-T6 adds strength for aerospace and structural parts. In stainless, 303 machines cleanly for fittings, 304 and 316 add corrosion resistance, and 17-4 PH adds strength after ageing. Steel wins on strength and cost. Brass is the fastest metal to machine and conducts well. Copper C110 is the conductivity benchmark, with C145 tellurium copper for machinability. Titanium and Inconel hold high-temperature strength but machine slowly and cost more. The material is the biggest lever on price, so it is selected for the service - load, environment, temperature - not by habit, and the grade is named on the drawing so the mill certificate confirms it.

Manual milling versus CNC

A manual milling machine is driven by a machinist who turns the handwheels; a CNC mill is driven by a program. Manual milling is right for one-offs, repairs and simple features where the setup would cost more than the part; CNC is right for anything that needs repeatability, a tight tolerance or more than a handful of parts. A stone-milling machine is a specialised tool for stone and masonry, and a mill-table is the workholding surface, not a machine - if you know the difference, you quote the right process.

When to reach for each

Reach for manual milling on a single, simple, non-critical part; reach for CNC on everything that must repeat or hold a band. This floor is CNC - 100+ machines at ±0.003 mm milled - because the parts buyers need are the ones that have to repeat. Contact Felipe Iglesias at [email protected] or +86 13126536955 with the drawing, and the process is chosen for the part, not the other way around.

The quality evidence behind every part

Every part ships with its evidence. Incoming stock is checked against the mill certificate - composition by XRF, hardness where specified - before machining. The first article is inspected in full against the drawing, critical characteristics run under statistical process control at Ppk 1.67 initial and Cpk 1.33 in production, and in-process checks hold the tolerance on a Hexagon CMM with the 10:1 gauge rule. The final report ships with the parts, so you get the product and the proof in one delivery - the line between a held tolerance and a claimed one.

your guide to quoting

Behind every good quote is a drawing that specifies. Name the material grade, not just the material; mark the datums and tolerances that actually matter; state the finish; and give a quantity, even a range. The more the drawing specifies, the less the shop assumes, and the closer the quote is to the real part. An itemised quote - material, setup, cycle time, inspection - lets you challenge the right line rather than negotiate blind, and it is the quickest path to a cheaper part: loosen a tolerance that does not matter, or raise the quantity to spread the setup. Send the drawing to Felipe Iglesias at [email protected] or +86 13126536955 and ask for it itemised.

De-risking a first order

Start with a handful of parts to confirm the routing and the tolerance, then scale. The same machines, the same inspection bench and the same certificate numbers apply to a single piece and a production run alike, so a small first batch is the proof that a large one will hold the same numbers.

What this shop actually runs

We machine every part in our own 6,800 m² plant in Dongguan, China, on 100+ CNC machines with 100+ staff. The machine list by category:

  • 5-axis machining centres (10+) - Mazak VARIAXIS I-600 (510/910/510 mm travel, 12,000 rpm, 22 kW, 71.6 N·m, 30-tool BT40) and Mazak INTEGREX I-250H S (B-axis 0.0001°, 24 kW, 124 N·m, 38-tool HSK-A63). Cut on compound-angle parts, single-setup multi-face prismatic work, and aerospace fittings where datum transfer loss is unacceptable.
  • 3-axis / 4-axis machining centres (50+) - Brother SPEEDIO S500Z2N / S700Z2N (10,000 rpm, 14/21-tool ATC, 0.7 s tool-to-tool, Z-axis 2.2 G) and Mazak VCE-430A L / VCE-570C L (10,000 rpm, 118 N·m, 24-tool ATC). Cut on prismatic parts, plates, brackets, housings.
  • Swiss-type turning centres (10+) - Citizen Cincom A20-3F7 (Φ20 mm, 10,000 rpm), TSUGAMI B0206-III / B0205-III (Φ20 mm, 0.1 µm), STAR SR-32JII / SR-32J Type N (Φ32 mm, 8,000 rpm). Cut on long, slender rotational parts at ±0.002 mm.
  • CNC turning centres (20+) - HEADMAN T70M/1250 (720 mm swing, 117 mm bore, 3,000 rpm, BMT75 12-station turret). Cut on shafts, bushings, flanges up to ±0.002 mm.
  • Wire EDM (5+) - Sodick AQ535L (550/350/300 mm travel, ±20° taper, 800 kg workpiece). Cut on hardened tool steel, internal splines, sharp internal corners that milling cannot reach.
  • Inspection: Hexagon CMM + 20+ gauges - Hexagon CMM for coordinate measurement, plus vision system, profilometer, hardness tester, coating thickness gauge, XRF for material verification. The 10:1 rule (gauge 10x more accurate than the band) is applied to every feature.
  • Machine highlights - VARIAXIS I-600: one-setup multi-face 5-axis + MAZA-CHECK auto-calibration; INTEGREX I-250H S: DONE-IN-ONE mill-turn, B-axis 0.0001° + Ai thermal shield; SPEEDIO S500Z2N / S700Z2N: Z-axis 2.2 G + 0.7 s ATC; Swiss-type: guide-bush switchable + 0.1 µm resolution.

Tolerance: ±0.003 mm CNC milling / ±0.002 mm CNC turning / ±0.002 mm grinding and wire EDM. Capability: Ppk >= 1.67 initial on key characteristics, Cpk >= 1.33 ongoing.

Certificates: ISO 9001:2015 (116024/A/0001/UK/En), IATF 16949:2016 (131941/A/0001/SM/En, with design clause 8.3 excluded, stated openly) and ISO 14001:2015 (116024/B/0001/UK/En), issued to Dongguan Zhuohang Ltd, registration 91441900MA4UWT6X39, founded 2005.

Where we ship: Austria, Belgium, the Czech Republic, Denmark, France, Germany, Greece, Hungary, Ireland, Italy, the Netherlands, Spain, Sweden and the United Kingdom in Europe; Brazil, Canada, Mexico and the United States in the Americas; China, Israel, Japan, Singapore and Sri Lanka in Asia; Australia and New Zealand in Oceania; and South Africa in Africa — plus other countries and regions worldwide, shipped from our base in Dongguan, China.

Contact: Felipe Iglesias, [email protected], +86 13126536955.

Not sure if your part needs 3, 4, or 5 axes? Send the drawing to [email protected] or use our process-selection guide for the right call and a transparent quote.

Frequently Asked Questions

When do I need 4-axis instead of 3-axis?

When your part has features on multiple sides or around its diameter that would otherwise require unclamping and re-fixturing on a 3-axis mill. The 4th axis holds those relationships in one setup and saves setup time.

Is 4-axis cheaper than 5-axis?

Usually yes, because the machine-hour rate is lower and programming is simpler. If your geometry only needs indexed rotation (not two-axis tilting), 4-axis is the efficient choice.

What tolerance does the rotary 4th axis hold?

In short, Position of around-axis features depends on the rotary table's indexing accuracy and how the part is located on it. Standard mill/turn tolerance is ±0.003 mm (milling) / ±0.002 mm (turning); the rotational relationship is governed by the table's repeatability, which a good shop verifies.

Standards referenced on this page

  • ASTM A276/A276M-17 — Standard Specification for Stainless Steel Bars and Shapes
  • ASTM B211/B211M-19 — Standard Specification for Aluminum-Alloy Rolled or Cold Finished Bar, Rod, and Wire
  • ISO 9001 — Quality management systems — Requirements